PCB Shielding Can Flatness Guide
Warpage Causes, Tolerance Recommendations and Practical Solutions
Flatness is critical to reliable SMT soldering, stable PCB grounding and consistent EMI/RFI shielding performance.
This guide explains what affects shielding can flatness, why shields may warp or lift after reflow, and how flatness can be improved through material, tooling, forming and inspection control.

What Is PCB Shielding Can Flatness?
Flatness describes how closely the soldering surface or bottom edge of a shielding can follows an ideal flat plane.
When the bottom edge is uneven, some areas may not contact the solder paste correctly, which can lead to lifting, incomplete solder joints or unstable grounding after reflow.

Why Flatness Is Important
Reliable SMT Soldering
A flat soldering edge improves contact with solder paste during reflow.
Stable PCB Grounding
Consistent contact helps maintain a low-resistance grounding path.
Better EMI Performance
Continuous grounding reduces potential leakage paths around the shield perimeter.
Consistent Assembly
Controlled flatness reduces rocking, lifting and placement instability.
What Causes Shielding Can Warpage?
Flatness is usually influenced by several factors rather than one single cause.
Material Properties
Material hardness, grain direction, thickness and residual stress all affect springback.
Part Size
Larger shielding cans are more sensitive to deformation and uneven stress distribution.
Wall Height
Higher walls and deeper forms generally increase forming stress and springback.
Forming Process
Multiple bends, deep drawing and asymmetric forming can introduce residual stress.
Tooling Precision
Tool alignment, clearance, wear and polishing directly influence flatness.
Reflow Heating
Uneven heating and cooling may cause temporary or permanent warpage.
Typical Flatness Tolerances
The final tolerance should be confirmed after reviewing the complete part geometry and application.
| Application Level | Typical Flatness Target | Notes |
|---|---|---|
| General PCB Shield | ≤ 0.10 mm | Suitable for many standard SMT applications |
| High-Precision Shield | ≤ 0.08 mm | Requires tighter tooling and process control |
| Special Requirement | ≤ 0.05 mm | Feasibility depends on size, material, height and geometry |

Why Do Shields Lift After Reflow?
Large or irregular shielding frames may heat and cool unevenly during reflow. Different thermal expansion rates across the part can temporarily distort the soldering edge.
Thin material, asymmetric geometry, residual forming stress, uneven solder paste and insufficient PCB support can increase the risk of lifting or incomplete wetting.
How to Improve Shielding Can Flatness
Optimize Tooling
Improve die alignment, forming clearance, support and calibration features.
Select Suitable Material
Choose the proper alloy temper and thickness for the geometry.
Balance the Structure
Avoid strongly asymmetric walls, openings and bend patterns where possible.
Control Forming Stress
Use progressive forming and optimized bend radii to reduce springback.
Add Calibration
A final restrike or flattening operation can improve bottom-edge consistency.
Maintain the Tool
Regular polishing and wear inspection help preserve forming accuracy.
Optimize Reflow Conditions
Review heating rate, peak temperature, cooling and board support.
Inspect Consistently
Use defined fixtures and measurement methods for repeatable results.
Flatness Inspection Methods
- Granite Surface Plate: Used as a stable reference plane.
- Feeler Gauge: Checks the maximum gap between the shield edge and reference surface.
- Height Gauge: Measures height variation at defined points.
- CMM or Optical Measurement: Suitable for detailed dimensional analysis.
- Dedicated Inspection Fixture: Improves speed and repeatability for production checks.

How Material Affects Flatness
Material type, temper and thickness must be selected together with the shield geometry.
| Material | Flatness Considerations | Typical Use |
|---|---|---|
| Tinplate | Good rigidity; coating and forming stress must be controlled | Cost-sensitive, high-volume shields |
| Nickel Silver | Good formability and stable solderability | Precision and high-reliability applications |
| Stainless Steel | High strength but greater springback and more difficult soldering | Special mechanical requirements |
Flatness vs Shield Height
As wall height increases, forming strain and springback generally become more difficult to control.
Taller shields may require additional forming stages, larger corner radii or a deep drawn structure.

Flatness vs Material Thickness
Thicker material usually improves rigidity but may require greater forming force and optimized tooling clearance.
Very thin material reduces weight and cost but is more sensitive to handling and thermal deformation.

Flatness Requirements by Industry
These values are general references only. Drawing requirements always take priority.
| Industry | Common Flatness Range | Design Considerations |
|---|---|---|
| Consumer Electronics | Around ≤ 0.10 mm | Cost and high-volume assembly |
| Telecommunication | Around ≤ 0.08–0.10 mm | Grounding and RF performance |
| Automotive Electronics | Project-specific, often tight | Reliability and thermal cycling |
| Medical & Industrial | Project-specific, commonly ≤ 0.05–0.08 mm | Long service life and stable assembly |

HEXIN Flatness Control
HEXIN reviews shielding can flatness together with material, thickness, size, wall height and forming method.
- Tooling design and manufacturability review
- Precision grinding and die alignment
- Progressive forming and calibration operations
- Tool maintenance and polishing
- Flatness inspection using dedicated methods
- Prototype verification before mass production
For general PCB shielding cans, a flatness target around ≤ 0.10 mm is common. High-precision projects may target ≤ 0.08 mm, while ≤ 0.05 mm requires a detailed feasibility review and tighter process control.
Frequently Asked Questions
Common questions about PCB shielding can flatness and warpage.
What is an acceptable flatness for a PCB shielding can?
A common target is ≤ 0.10 mm, but the correct requirement depends on part size, solder pad design and application.
Can shielding can flatness reach 0.05 mm?
It may be possible for suitable designs, but size, material, thickness, height and tooling must be reviewed.
Why is my shielding can warped?
Common causes include residual forming stress, asymmetric geometry, thin material, tooling condition and handling.
Does material thickness affect flatness?
Yes. Thicker material is usually more rigid, while thinner material is more sensitive to deformation.
Does reflow soldering affect shield flatness?
Yes. Uneven heating and cooling may cause temporary or permanent warpage.
How is shielding can flatness measured?
Common methods include a granite plate, feeler gauge, height gauge, CMM or dedicated fixture.
Is nickel silver flatter than tinplate?
Not automatically. Geometry, temper, thickness and tooling are often more important than material name alone.
Can deep drawn shields achieve good flatness?
Yes, but drawing stress, wall height and trimming design must be controlled.
What causes springback in shielding cans?
Springback is caused by elastic recovery after forming and depends on material strength, bend radius and tooling.
Can HEXIN guarantee a specific flatness?
A flatness commitment can be confirmed after reviewing the drawing, material and production process.
Need Help Solving Shield Flatness Problems?
Send us your drawing, material, thickness, quantity and required flatness. Our engineering team will review the structure and recommend a practical manufacturing solution.
